Updated November 2026
Learning how to tie fishing lures lets you build baits that match local forage, fill gaps in your tackle box, and cost far less than buying finished products. In this guide you will learn the tools and materials you need, how to tie three common lure types (a jig, a bucktail-style spinner rig, and a simple soft-plastic rig), and the mistakes that cause lures to fail in the water. Basic hand skills are enough to get started, and a few dollars of materials can produce dozens of baits.
What You Need Before You Start
Most lure tying uses the same small set of supplies. Gather these before you sit down so you are not stopping mid-wrap to hunt for something.
Shopping for one? See our guide: 5 Best Bass Assassin Fishing Lures of 2026: Picks Compared.
- Hooks: Choose a style for the lure you plan to build. Jig hooks have a bent shank and an eye that sits in line with the point. Octopus or wide-gap hooks suit soft plastics and spinners.
- Thread: Use bonded nylon or Kevlar-reinforced thread. Size 210 denier is a common all-purpose choice for freshwater baits.
- Bobbin and thread tension tool: A bobbin holds the spool and keeps tension steady as you wrap.
- Whip finisher or half-hitch tool: This locks the thread so the wraps do not unravel.
- Bucktail, feathers, or soft-plastic bodies: These provide the profile and action.
- Head-cure epoxy or UV resin: Use it on jig heads and painted bodies to protect the finish.
- Scissors, bodkin, and a small vise: A vise holds the hook steady so you can work with both hands.
How to Tie a Basic Bucktail Jig
A bucktail jig is one of the easiest lures to tie and one of the most versatile. The steps below work for most jig hooks in the 1/8 to 3/8 ounce range.
Step 1: Secure the Hook
Clamp the hook in the vise with the eye facing you and the point up. Keep the jaw tight enough that the hook does not rotate, but avoid crushing the wire.
Step 2: Start the Thread
Lay a few wraps of thread starting just behind the eye and working back toward the bend. Leave the thread end long so you can anchor the tail later. Wrap back to the starting point, which gives you a smooth base for the hair.
Step 3: Tie in the Tail Hair
Cut a small clump of bucktail, roughly the thickness of a pencil. Remove the short underfur and fine pieces from the base. Hold the hair along the top of the shank, with the tips extending past the bend by about one-third to one-half the length of the hook. Make two or three tight wraps over the butt ends, then add a few more to secure it firmly.
Step 4: Add Flash or Color
If you want flash, tie in a few strands of Flashabou or similar material on top of the hair, using the same wrapping method. Keep the materials thin so the profile stays slim.
Step 5: Build the Head
Wrap thread forward to form a smooth, tapered head about the size of the hook eye. Whip finish at the eye, cut the thread, and check that the head is even and the tail sits straight.
Step 6: Finish and Cure
Apply a thin coat of head-cure epoxy to the thread head. Let it cure fully according to the product directions before fishing. Many tiers rotate the jig in the vise while it sets to keep the head round.
How to Build a Simple Spinner Rig
A spinner rig uses a blade that spins around a wire shaft as you retrieve. Tying your own lets you swap blade sizes and colors for different water clarity and current.
Step 1: Assemble the Wire Shaft
Slide a bead onto the wire shaft, then add the clevis that holds the blade. Thread a second bead on before attaching the hook at the end of the shaft.
Step 2: Attach the Blade
Place the blade on the clevis so it can rotate freely. Test the spin by holding the wire and turning it gently. The blade should turn smoothly without catching on the clevis.
Step 3: Tie the Skirt or Dressing
Add a skirt of marabou, silicone, or hair above the hook if you want a fuller profile. Secure the material with thread wraps, then whip finish.
Step 4: Balance the Lure
Hold the finished rig by the line tie. It should hang with the hook slightly below the wire, not tipped to one side. Adjust the dressing or hook placement if needed.
How to Rig a Soft-Plastic Bait
Soft plastics are the simplest of the three to rig, since you are mostly threading the hook through the body. The main decision is the rigging style.
- Texas rig: Insert the hook point into the head, run it through the body, and bring the point back out. Bury the eye and point in the plastic so the bait weedless.
- Weedless wacky rig: Pass the hook through the middle of the worm, leaving equal length on each side. The bait falls with a slow, shimmy action.
- Shaky head: Thread the bait onto a jighead, then push the hook point into the body and out again so the bait sits straight.
Choosing Hooks and Materials by Lure Type
Matching the hook and material to the lure job prevents most problems. The table below gives a starting point.
| Lure type | Typical hook | Best material | Common target |
|---|---|---|---|
| Bucktail jig | Jig hook, 1/8 to 3/8 oz | Bucktail, flash | Walleye, bass |
| Spinner | Single or treble hook | Blade, skirt | Trout, pike |
| Soft plastic | Worm hook, offset hook | Plastic body | Bass, panfish |
| Fly-style streamer | Streamer hook | Feathers, marabou | Trout, bass |
If you are still deciding which style fits your local water, How to Choose Fishing Lures for Different Fish and Water covers how clarity, cover, and species shape the choice. For rigging ideas beyond these basics, see How to Rig Your Tackle for Different Fishing Lures.
Tips for Better Results
- Work in good light and keep your thread organized on the bobbin so tension stays even.
- Tie a few spares for each pattern. A failed wrap is easier to fix when you have backups.
- Test each finished lure in a sink or bucket before taking it to the water. Check that it swims or falls the way you expect.
- Keep a log of what works. Note the color, size, and conditions so you can refine your patterns.
- If a spinner blade feels stiff or the clevis binds, swap it out rather than forcing it. Spinner Blades for Fishing Lures: How to Choose and Swap Them (Step-by-Step) explains how to match blades to the water.
Common Mistakes
- Too much hair or material: Overloaded bucktail or dressing hangs unevenly and reduces action. Start with less and add more only if the profile looks thin.
- Loose thread wraps: Loose wraps slip under load. Keep tension steady and make sure the whip finish is snug.
- Skipping the cure: Fishing a jig before the epoxy sets can smear the head and expose the thread.
- Using the wrong hook for the bait: A hook that is too light for a heavy jig bends in use. Match hook wire to the weight and fish you expect.
- Ignoring balance: Lures that tip to one side run off-line. Check balance before you tie the final components.
Recommended gear
A basic rotary vise and a good bobbin make the biggest difference for consistency. Pick tools that hold the hook firmly and keep thread tension even.
- Rotary vise: A rotating head lets you check every side of the jig as you wrap, which helps keep the head even. View on Amazon
- Tension bobbin: Keeps thread tension steady so wraps stay tight without snapping the thread. View on Amazon
- Head-cure epoxy: Protects jig heads and painted bodies from chips and water damage. View on Amazon
- Bucktail hair pack: Pre-cut natural hair in a range of colors saves time sorting and cleaning material. View on Amazon
FAQ
What is the easiest fishing lure to tie as a beginner?
A basic bucktail jig is usually the easiest starting point. It uses one hook, a single material, and a short sequence of wraps.
What thread should I use for tying lures?
Bonded nylon or Kevlar-reinforced thread in the 210 denier range works well for most freshwater lures. Heavier thread suits larger baits.
Do I need a vise to tie fishing lures?
A vise is strongly recommended because it holds the hook steady and frees both hands. You can improvise with a clamp for very simple rigs, but results are less consistent.
How long does head-cure epoxy take to dry?
Drying time depends on the product and the room temperature. Follow the directions on your specific epoxy and allow it to cure completely before fishing.
Can I tie lures that will catch saltwater fish?
Yes, but saltwater requires corrosion-resistant hooks and wire, and some materials degrade faster in salt. Check hook and wire ratings before you tie for that environment.
How do I keep my tied lures from rusting?
Rinse lures with fresh water after use, dry them thoroughly, and store them in a dry box. Stainless hooks resist rust better than plain carbon steel.
Is tying my own lures cheaper than buying them?
Tying your own lures usually reduces the cost per bait once you have the tools. Hooks, materials, and epoxy are the main ongoing supplies.
Conclusion
Learning how to tie fishing lures starts with a few reliable tools, a clear plan for each lure type, and steady wrapping technique. Practice the bucktail jig first, then move on to spinners and soft-plastic rigs as your hands get comfortable. Test your work before you fish it, and keep notes on what catches fish in your waters. Over time, your own patterns can become some of the most productive baits in your box.

