Updated November 2026

To tie fishing line to a conventional reel, you attach the line to the spool’s arbor with an arbor knot, then wind it on under steady tension. The result is a line that won’t slip under load, spools evenly and holds up when a fish makes a hard run. The process takes about two minutes once you know the steps.

What You Need Before You Start

Gather everything first so you aren’t fumbling with line halfway through. Conventional reels are often spooled with monofilament or braid, and the knot you choose depends on what you’re using.

Shopping for one? See our guide: Conventional Fishing Reel vs Baitcasting: Which Should You Choose?.

  • Fresh fishing line in the pound test or braid strength your rod is rated for
  • A pair of line clippers or sharp scissors
  • A dry cloth or towel to hold the line and keep it from slipping
  • A pencil or dowel (optional, for holding the spool)
  • Your reel, with the spool removed from the frame if your model allows

Step-by-Step: Tying the Arbor Knot

The arbor knot is the standard choice for attaching line to a reel spool. It grips the spool’s central core (the arbor) so the line pulls against the spool rather than slipping off it.

  1. Wrap the line around the bare arbor of the spool, about two full turns.
  2. Tie an overhand knot around the standing line (the part leading back to the reel), pulling it snug against the arbor.
  3. Tie a second overhand knot around the tag end, then pull both ends firmly to seat the knot.
  4. Trim the tag end to about 1/8 inch so it doesn’t catch on the reel or your fingers.

Spooling the Line Under Tension

Even tension during spooling prevents line from bunching, crossing and creating weak spots. Loose winding is a common cause of tangles on the next cast.

Hold the spool with a pencil or dowel passed through the center, or have a helper hold it. Then pinch the line between your thumb and forefinger with a cloth or towel, applying light pressure as the reel turns. Wind the line in tight, even layers, filling the spool to about 1/8 inch below the lip. Overfilling causes line to jump off during casts, while underfilling reduces casting distance.

Checking Your Knot and Line

Before you cast, confirm the connection is secure. Give the line a firm tug and watch the knot as it slides against the spool. A correctly tied arbor knot tightens and holds instead of creeping. If the line slips even slightly, retie the knot before you fish.

If you’re using a leader, attach it to your main line with a separate knot. The How to Choose and Tie a Fishing Leader Line guide covers that connection in detail.

Common Mistakes

  • Skipping the second overhand knot, which lets the arbor knot loosen under load.
  • Spooling without tension, causing bird’s nests and uneven line lay.
  • Filling the spool to the rim, which increases the chance of line jumping during a cast.
  • Leaving the tag end too long, which can snag on guides or your hand.
  • Using old line with nicks or kinks, which weakens the knot before the fish ever bites.

A pair of sharp line clippers makes clean trims that won’t fray the tag end. Look for a compact pair you can keep in your tackle bag.

View on Amazon

A small spool holder or fishing line spooler keeps the spool steady, so you can apply even tension without needing a helper.

View on Amazon

Braided line is popular on conventional reels for its strength and thin diameter. Choosing a line that matches your rod’s rating helps the knot perform as intended.

View on Amazon

FAQ

What knot is best for tying line to a conventional reel?

The arbor knot is the standard choice because it grips the spool’s core and resists slipping. Most anglers use it with both monofilament and braided line.

How much line should I leave on the spool?

Fill the spool to about 1/8 inch below the lip. This leaves room for smooth casting without overfilling.

Why does my line keep slipping on the spool?

Slipping usually means the arbor knot wasn’t seated tightly or lacks a second overhand knot. Retie the connection, pull both ends firmly, and check it again before fishing.

Conclusion

Tying line to a conventional reel comes down to a secure arbor knot and even spooling under tension. Once you’ve practiced the steps a couple of times, the whole process becomes quick and reliable. Check the knot before every trip and retie it whenever it looks loose.

Claire Whitaker

About Claire Whitaker

Claire Whitaker is part of our editorial team and reviews and edits our freshwater fishing tackle on a budget guides, checking product details against manufacturer specifications and owner feedback.