Updated November 2026
Wall mount fishing rod holders keep your rods off the floor, off the truck bed and out of the way of pets and kids. This guide walks you through choosing the right style, finding a solid spot on the wall and mounting the holders so they hold up over time. Most of the work takes an afternoon with basic hand tools.
Choose the Right Type of Wall Mount Holder
Wall mount fishing rod holders come in three common styles. Horizontal rack bars hold several rods side by side and suit a garage or shed wall. Vertical clips or cradles hold one or two rods upright and take up less space. Rod-and-reel combo slots have larger openings for reels, so choose these if your setups are already rigged.
Shopping for one? See our guide: 3 Best Fishing Pole Rod Holder Picks for Garage, Boat, and Ground Use.
Look at the rod diameter at the butt section, not just the tip. Check the mount’s opening or cradle width against your thickest rod. If you own a mix of spinning and casting rods, a holder with adjustable or padded arms will save you from replacing it later. For a wider look at options, see 29 Best Fishing Rod Holders.
Pick a Mounting Spot and Check the Wall
The wall needs to be solid enough to carry the weight of every rod and reel you plan to store. Wood studs and masonry are both good anchors. Hollow drywall alone is not.
- Use a stud finder to locate framing members, and mark the center of each stud with painter’s tape.
- Plan the height so the butt ends sit at a comfortable reach, usually between 4 and 6 feet off the floor, and keep the rods clear of door swings and vehicle doors.
- Leave enough clearance so reels do not hit the wall or adjacent holders.
How to Install Wall Mount Fishing Rod Holders
Once the location is set, the install is straightforward. You will need a drill with bits matched to your fasteners, a level, a tape measure, a pencil and a screwdriver or driver bit. A related read: Ice Fishing Rod Holder Wall Mount: A Step-by-Step Guide for Your Shanty.
- Hold the holder against the wall at the marked height and check it with a level in both directions.
- Mark the mounting hole locations with a pencil, then drill pilot holes slightly smaller than the screw diameter.
- Drive lag screws or heavy wood screws into studs. For masonry, use the anchors the manufacturer specifies.
- Tighten each fastener until the holder is firm, but avoid stripping the screw head or cracking the wall material.
- Test the mount with a light tug, then slide a rod in and out to confirm it seats smoothly.
Manufacturers typically specify fastener sizes and maximum load for each holder, so follow their instructions closely. If you are unsure about the wall structure, a general contractor or handyman can confirm the mounting is secure.
Compare Common Mounting Setups
| Holder style | Best for | Space needed |
|---|---|---|
| Horizontal rack bar | Storing 4 or more rods | Long, narrow wall section |
| Vertical clip or cradle | 1 to 3 rods, tight spaces | Small vertical strip |
| Rod-and-reel slot | Rigged combos, reels attached | Wall space plus reel clearance |
Tips and Common Mistakes to Avoid
- Do not mount into drywall alone. Always hit studs or use anchors rated for the load.
- Keep reels clear of the wall so the handles and drag knobs do not get bumped.
- Store rods with the tip pointing up or horizontal, not hanging by the tip, to avoid bending.
- Check the screws every few months, especially in a garage where temperatures swing.
- Wipe down rods after saltwater or muddy trips before racking them to prevent grime buildup on the guides. For that, see How to Clean Fishing Rods.
Recommended Gear
- Stud finder: A reliable stud finder helps you locate solid framing so the holder carries its load safely. View on Amazon
- Cordless drill and driver set: Useful for drilling pilot holes and driving lag screws without fighting the wall. View on Amazon
- Torpedo level: A small level keeps the rack straight so rods sit evenly and do not slide off. View on Amazon
FAQ
Can I mount a rod holder on drywall without studs?
Not safely for a loaded rack. Drywall alone cannot carry the weight of several rods and reels, so attach the holder into studs or use anchors rated for the load.
How high should wall mount fishing rod holders be placed?
Most people mount them between 4 and 6 feet off the floor so the butt ends are easy to reach. Adjust the height so the reels clear the wall and nearby doors.
Do wall mount holders damage rods over time?
They can if rods are stored by the tips or crowded together. Support rods at the butt and midsection, and keep the tips free so the blanks do not bend or warp.
Conclusion
Wall mount fishing rod holders work best when they match your rod sizes, sit into solid framing and clear your reels. Plan the height and spacing before you drill, and check the fasteners every few months. A careful install will keep your rods ready to grab and protected for years.

